Gland packing is a small, cheap part. It is also the reason a pump gets pulled off the line. The braided packing sits in the stuffing box and seals the gap around a shaft or valve stem. Pick the wrong material and it leaks, scores the shaft or burns out early.
The question comes up often: asbestos or non-asbestos? This guide explains the difference, what to check for your own equipment, and why new requirements should go to asbestos-free options such as PTFE graphite gland packing.
What Is Asbestos Gland Packing?
Asbestos gland packing is braided from asbestos fibre, usually with a lubricant or binder added so it can be packed into the stuffing box. For decades it was a common choice on steam valves, hot-water pumps and other hot services, because the fibre copes well with heat.
The problem is the fibre. The World Health Organization identifies all forms of asbestos as carcinogenic to humans. Fibres can be released when old packing is cut, pulled out or left to dry and crumble, and that is exactly what happens during maintenance. For this reason, asbestos packing should not be specified for new installations.
Some older plants still have it in service, and the rules on its use sit under Indian regulations that every buyer should check. The asbestos industrial materials we list are described for factual reference only, and any use must stay within what the law allows.
What Is Non-Asbestos Gland Packing?
Non-asbestos packing replaces the asbestos fibre with other materials. The usual ones are PTFE, graphite and synthetic fibres such as aramid, often braided together. PTFE brings chemical resistance and a low-friction surface. Graphite helps move heat away and lubricates the shaft. Synthetic fibres add strength to the braid.
PTFE graphite braided packing is the combination most buyers meet on pumps and valves. You can see the forms we supply under our non-asbestos sealing products. Grades differ between makers, so treat the material name as a starting point and not as a guarantee.
Asbestos vs Non-Asbestos Gland Packing: Key Differences
This table puts the two side by side.
| Comparison factor | Asbestos gland packing | Non-asbestos gland packing |
|---|---|---|
| Material | Asbestos-based fibres | PTFE, graphite and other synthetic fibres |
| Heat resistance | Depends on grade and construction | Depends on material composition and grade |
| Chemical resistance | Depends on composition | Depends on the selected material |
| Applications | Traditional industrial sealing applications | Pumps, valves and other industrial sealing applications |
| Safety | Significant health hazards from fibre exposure | Avoids asbestos-related fibre hazards |
| Selection | Subject to applicable legal restrictions | Select according to operating conditions and manufacturer specifications |
One caution. Non-asbestos packing is not automatically better on temperature, pressure or service life. Those depend on the exact grade and how the braid is built. The safety row is the only one that does not change with the grade.
Factors to Consider When Choosing Gland Packing
Write these down before you ask any supplier for a quote.
Temperature
Use the highest temperature at the stuffing box, not the average process temperature. Friction at the shaft adds heat. Compare the number with the maximum the manufacturer states for that grade.
Pressure
Note both normal and peak pressure. Higher-pressure duties may need a particular construction, and the datasheet will say so.
Shaft Speed
A fast rotating shaft creates far more friction than a slow valve stem. Rotating and reciprocating duties usually need different packing. Speed is the detail most often left out of an enquiry.
Chemical Compatibility
List every fluid the packing will touch, including cleaning chemicals. A packing that handles one medium well can break down in another.
Equipment Type and Operating Environment
Pumps, valves and agitators all seal differently. Dust, moisture and outdoor exposure matter too, and so does the condition of the shaft or sleeve. A worn shaft will chew through good packing.
Whatever you shortlist, ask for the grade specification, and read what the supplier says about quality and product specifications before you order.
Which Gland Packing Is Right for Your Application?
Start from your operating data and work towards the material, not the other way round.
For most pumps and valves handling chemicals or general process fluids, a non-asbestos packing is the practical answer. PTFE graphite suits many chemical and mixed-duty pumps, as long as the duty stays inside the grade’s rated limits.
For very hot services, check graphite-based and other high-temperature non-asbestos grades against their datasheets. Do not assume. Ask for a recommendation based on your actual numbers.
If you are replacing existing asbestos packing, treat the removal as a hazardous job. Follow the handling and disposal rules that apply in India, and bring in a qualified person if you are unsure.
Why Choose Non-Asbestos Gland Packing?
The biggest reason is health. Non-asbestos packing takes the asbestos fibre hazard out of your maintenance crew’s work. It also reduces the compliance questions that come with asbestos. And there are now enough grades that most duties have an asbestos-free option. The real work is picking the right grade for your conditions.
Frequently Asked Questions
What is the difference between asbestos and non-asbestos gland packing?
Asbestos packing is braided from asbestos fibre. Non-asbestos packing uses materials such as PTFE, graphite and synthetic fibres. The main difference is safety, since asbestos fibre is a recognised carcinogen. Heat and chemical performance depend on the grade of either type, so compare datasheets, not material names.
What materials are used in non-asbestos gland packing?
Common materials are PTFE, graphite, aramid and other synthetic fibres, sometimes with carbon-based fibres. They are usually braided, often in combination, and may carry a lubricant. Each combination suits different temperatures, speeds and chemicals, so the right choice depends on your duty.
Is PTFE graphite gland packing suitable for industrial pumps?
It is widely used on industrial pumps and valves, mainly because PTFE resists many chemicals and graphite helps with heat and lubrication. Suitability still depends on the grade, shaft speed, temperature and pressure. Check the datasheet limits, or send us your operating details and we will help you shortlist.
How do temperature and pressure affect gland packing selection?
Each grade has maximum temperature and pressure limits set by its maker. Use the highest values the stuffing box will see, including friction heat, not just the process average. Packing run beyond its limits tends to harden, leak or wear the shaft, so keep a margin.
What should industries consider when replacing existing asbestos gland packing?
Choose the replacement grade from your temperature, pressure, shaft speed and fluid data. Check the shaft or sleeve condition. Then handle the old packing as a hazardous job: follow the Indian regulations on removal and disposal, and use trained people if you are unsure.
Conclusion
Choosing gland packing comes down to matching a grade to your real operating conditions and, for new work, choosing an asbestos-free grade. Note down the temperature, pressure, shaft speed, chemicals and equipment type, then compare them with datasheets. Shiv Asbestos Co. supplies industrial gasket and sealing products from Vadodara and can help with that comparison.
Looking for suitable non-asbestos gland packing for your industrial application? Explore Shiv Asbestos Co.’s PTFE products or contact our team to discuss your requirements.